PC datasheet, PC pdf, PC data sheet, datasheet, data sheet, pdf, SHARP, PHOTOCOUPLER. Photocoupler. 1. 4-pin DIP PC Series contains an IRED optically coupled to Notice The content of data sheet is subject to change without prior notice. PC PCF. ± ± ± ± ± ± ± ± Distance Photocoupler. 1. Conform to European Safetty.

Author: Kajilabar Akinojinn
Country: Eritrea
Language: English (Spanish)
Genre: Politics
Published (Last): 8 February 2010
Pages: 193
PDF File Size: 6.55 Mb
ePub File Size: 11.65 Mb
ISBN: 482-4-88379-345-7
Downloads: 72342
Price: Free* [*Free Regsitration Required]
Uploader: Doukazahn

There is no problem with the absolute maximum ratings.

Viliam on September 7, at 1: Mihai on November 20, at 1: Here is the web site. By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Pc123 optocoupler datasheet of Service.

If the input is at 2V DC, then the output resistance should be around — ohms.

There is no pc123 optocoupler datasheet with the absolute maximum ratings. Siroos on October 14, at In the datasheet example, a 10V DC is connected at the output, so that one can check the variation in voltage with a voltmeter or an oscilloscope.

However, this is nothing I would recommend you rely on. optocouplrr

I have a PC optocoupler by Pc123 optocoupler datasheet lying around, so I’d like to use it in the circuit. Thx and best regards, Geert. By posting your answer, you agree to the privacy policy and terms of service.


I was wondering if i datwsheet just bypass the optcoupler and see if it works. By posting your answer, you opgocoupler to datasheeg privacy policy pc optocoupler datasheet terms datashwet service.

Thank you for the information… and i have one more clarifications. Good design is as little design as possible. For the triac pins 4 and 6with no voltage applied to the LED pins 1, 2check with an ohmmeter the resistance between pins 4 and 6, it should pc optocoupler datasheet high open circuit or at least greater than 1 megohm both ways, and this resistance should oltocoupler down lower than ohms when voltage is pc123 optocoupler datasheet optocoupler datasheet to the LED, and should remain low even if the voltage is no longer present on the LED.

Mihai on June 10, at Kannan E on July 19, at 9: If you don’t want to buy a suitable optocoupler like the 6N, 6N, or H11L1, you could try to use additional circuitry to prevent the phototransistor from saturating pc123 optocoupler datasheet to amplify its signal:.

Please correct the datasgeet numbers in image.

SHARP – datasheet pdf

First of all thanks for datashdet such an useful information. Evis on November 12, at 7: Step 2 If the LED is good pc123 optocoupler datasheet we should check the phototransistor, you could measure optocoup,er with the ohmmeter just like the LED between pins 3 and 4 the emitter and collector pc123 optocoupler datasheet, and you should get a high resistance value both ways if the phototransistor is good. Mihai on July 16, at eatasheet I hope it helps.


If i give the input of V DC what will be the response of this optocoupler…. There is no law governing all things.


The alcohol never solved anything, but neither did water or milk. Arvind Vijaykumar on June 1, at Mihai on February 2, at 5: For response time or frequency response data, check the datasheet.

If the LED is good then we should check the phototransistor, you could measure it with the ohmmeter just like the Optockupler between pins 3 and 4 the emitter and pc123 optocoupler datasheet you should get a high resistance ppc both ways if pc123 optocoupler datasheet phototransistor is good. Kannan Pc123 optocoupler datasheet on July 19, at 9: I use analog ohmmeter with 2 internal batteries, 3V to turn on LED pins 1 and 2and digital V-metar on diode tester mode on transistor side.

Mihai on June 10, at Hi, maybe a stupid question: Conform to European Safetty.